Jump Main Menu. Go directly to the main content

Grupo Cementos Portland ValderrivasGrupo Cementos Portland Valderrivas

  • We produce in a sustainable manner caring for the planet

  • We operate in Europe, Africa and United States

  • Cement, concrete, aggregate, mortar and recycling

  • The architectural challenges are built with us

  • We’re leaders in our markets

  • Specific cements and experienced teams

  • From the seashore we arrive where is needed

  • Committed to quality and the environment

  • We make It happen

You are in:
  1. Mortar - Bagged mortar - Products and recommendations - Pavement - Valsec Autonivel Fino

Mortar - Bagged mortar - Products and recommendations - Pavement - Valsec Autonivel Fino

Product range: Pavement

Technical mortar: Valsec Autonivel Fino

Self-levelling mortar for thin layers.

Self-levelling mortar for application in thin layers (2-5 mm).

Type CT C20 F6 A12 (UNE EN 13813).

Scope of application

Indoor applications. Smoothing and levelling of concrete, mortar and equivalent surfaces. Suitable as a base for laying tiles, stone, wood, parquet, carpet, etc.

Supply conditions

Bagged (25 kg. bags).



Mixing instructions

The mix can be prepared manually or mechanically. Mix the mortar with clean water (approximately 24%) to obtain a smooth paste with the required consistency. Use the same water proportion and mixing time throughout a given application.

The consistency should enable the paste to flow smoothly. Too much water may lead the paste to disaggregate. Do not use any admixtures without authorisation from the manufacturer. Maximum mixing time before application is 35 minutes, depending on weather conditions.

Substrate preparation

The substrate to be levelled must fulfil the following conditions:

  • It must be strong, clean and stable. There should not be any residues of gypsum, paint, waterproof coatings, etc.
  • The substrate must be flat; any holes or uneven areas must be filled.
  • In the case of non-porous substrates, apply a primer or roughen mechanically.
  • Respect structural, expansion and other joints.

Mortar made from cement, aggregate, organic and inorganic admixtures, which provide high self-levelling capacity, high adhesion and fast setting.

Product characteristics
Granulometry (max.) 2 mm Water proportion 24 ± 2%
Working time Approximately 35 minutes Consistency 220 - 240 mm
Compressive strength (UNE EN 1015-11) ≥ 20 Mpa Apparent density  1,4 ± 0,1 kg/m3
Flexural strength (UNE EN 1015-11) ≥ 6 Mpa  Working temperature +5ºC a +35ºC
Wear resistance (Böhme) (EN 13892-3) ≤ 12 cm3 / 50 cm2 Approximate yield / mm 1,5 ± 0,2 kg/m2
Application thickness 2 a 5 cm Fire resistance A1
Instructions for application

Pour the product on the floor and spread it with a float, spatula or similar tool to obtained the desired level and cover the desired area. The layer should not be more than 5 mm thick. Leave to dry for 24 hours before walking or painting, and wait 7 days before placing loads on the surface.

To tile, first polish the surface to improve adhesion and apply tiles with VALCOL adhesive cement (see datasheets). Do not use if there is a risk of rain or frost. Work at temperatures between 5ºC and 35ºC.


VALSEC AUTONIVEL FINO fulfils all the obligatory quality standards under UNE EN 13813.

VALSEC industrial mortars are produced in industrial dry mortar plants with quality assurance systems certified by AENOR in accordance with the UNE EN ISO 9001:2000 standard.

The data is based on trials performed in our control laboratory and is the result of extensive experience with the products made by the Cementos Portland Valderrivas Group. Variations in working conditions on site may lead to changes in performance.


Store in a dry place, protected from frost and direct sunlight. If properly stored, the product may be used up to 12 months after manufacture.


This product contains cement. Avoid contact with eyes and skin, and do not inhale the dust. Use rubber gloves and goggles when handling. Keep out of reach of children.

Note: Cementos Portland Valderrivas is not responsible for inappropriate use of the product or for unexpected outcomes arising from its usage, since the application conditions and methods are beyond our control. The customer is responsible for ensuring correct use of the product.

© Cementos Portland Valderrivas 2010. All rights reserved.