Cerrar

Jump Main Menu. Go directly to the main content

Grupo Cementos Portland ValderrivasGrupo Cementos Portland Valderrivas

  • We produce in a sustainable manner caring for the planet

  • We operate in Europe, Africa and United States

  • Cement, concrete, aggregate, mortar and recycling

  • The architectural challenges are built with us

  • We’re leaders in our markets

  • Specific cements and experienced teams

  • From the seashore we arrive where is needed

  • Committed to quality and the environment

  • We make It happen

You are in:
  1. Mortar - Bagged mortar - Products and recommendations - Technical mortar - Valsec Reparación

Mortar - Bagged mortar - Products and recommendations - Technical mortar - Valsec Reparación

Product range: Technical mortar

Valsec Reparación

High-performance mortar for repairing concrete.

Universal thixotropic mortar for repairing concrete and levelling concrete surfaces.

Scope of application

Outdoor and indoor use. Repairing concrete elements such as corners of balconies or beams, façades, walls, stairs and precast components; also for levelling vertical surfaces, etc.

Supply conditions

25 kg bags protected by plastic sheet.

Colours

Grey.

Mixing instructions

Mix VALSEC REPARACIÓN with 17% clean water to obtain a smooth paste. The mix can be prepared manually or mechanically.

The working time is 30 minutes depending on the environmental conditions. When preparing the mortar, use the same amount of water and mixing time for the entire process. Do not re-mix or use any admixtures without authorisation from the manufacturer.

Substrate preparation

Substrates must fulfil the following conditions:

  • They must be strong, rough, clean and stable.
  • Do not use on water-repellent substrates or on substrates with plaster, paint or plastic coating.
  • Defective areas must be cleaned and chiselled.
  • Restore or remove rusted or damaged reinforcement.
  • In very porous concrete surfaces, dampen the substrate before application.
Instructions for application

Lay the mortar on the substrate using a trowel, filling the surface to be repaired, and compacting the product. For layers over 10 mm thick, apply in successive layers of 5 mm max. Wait until the previous layer has hardened before applying a new layer. Power trowel the surface about 40 minutes after application.

Characteristics

Mortar made from cement, graded aggregate, organic and inorganic admixtures and fibres, which provides high mechanical strength, high adhesion and no shrinkage.

Type R3 (UNE EN 1504-3)
Granulometry (max.) 1,5 mm Water proportion 17% ± 1%
Working time Approximately 30 minutes Apparent density 1,8 ± 0,1 kg/m3
Initial setting time 50-80 min. Working temperature +5ºC a +35ºC
Final setting time 70-130 min. Layer thickness 5 mm
Water absorption by capillarity (EN 13057) < 0,5 kg/m2 h1/2 Approximate yield 20 ± 2 kg/m2
Adhesion (EN 1542) ≥ 1,5 Mpa Fire resistance (UNE EN 13501-1) A1
Compressive strength (EN 12190) ≥ 25 Mpa    
Quality

VALSEC REPARACIÓN (R3) fulfils all the obligatory quality standards under UNE EN 1504-3.

VALSEC mortars are produced in industrial dry mortar plants with quality assurance systems certified by AENOR in accordance with the UNE EN ISO 9001:2000 standard.

The data is based on trials performed in our control laboratory and is the result of extensive experience with the products made by the Cementos Portland Valderrivas Group. Variations in working conditions on site may lead to changes in performance.

Storage

Store in a dry place, protected from frost and direct sunlight. If properly stored, the product may be used up to 12 months after manufacture.

Safety

This product contains cement. Avoid contact with eyes and skin, and do not inhale the dust. Use rubber gloves and goggles when handling. Keep out of reach of children. Do not use the product at an ambient temperature below 5ºC or above 35ºC.


Note: Cementos Portland Valderrivas is not responsible for inappropriate use of the product or for unexpected outcomes arising from its usage, since the application conditions and methods are beyond our control. The customer is responsible for ensuring correct use of the product.

© Cementos Portland Valderrivas 2018. All rights reserved.